{"title":"Motorsports Cargo","description":"\u003cp\u003eWith EQ Systems’ hydraulic lifting systems, we make parking and setting up your Motorsports Trailer a breeze. With our Hydraulic Lifting System, you can quickly and safely secure your Motorsports Trailer with one touch of a button – no more manual labor or guesswork.\u003c\/p\u003e\n\u003cp\u003ePlus, it’s easy to maintain, so you can enjoy your leisure time worry-free!\u003c\/p\u003e\n\u003cp\u003eWe are located in Cassopolis, Michigan, at 19300 Grange St, Cassopolis, MI 49031 for installations.\u003c\/p\u003e","products":[{"product_id":"aj-2-24-jack-system","title":"AJ 2\/24 Jack System","description":"\u003ch3\u003eAJ hydraulic trailer jack, dual leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete dual leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AJ series is the 3.5\" x 3.5\" square tube in tube jack, and this system lifts 16,000 lbs across the two legs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAJ series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e16,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e3.5\" x 3.5\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eScrew drive output shaft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: screw drive\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is driven by hand through the output shaft on the end of the motor. Remove the pump top cover, then the silver sticker on the end of the motor, and drive the override coupler with a drill capable of at least 2000 rpm, using a 1\/4 inch (6mm) Allen drive hex key. Take care that the drill does not contact wires or hoses. The drill has to reach 2000 rpm or the pump will not develop enough pressure to move the jack.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-aj-hydraulic-trailer-jacks\"\u003e70487\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AJ dual leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/aj-70-cylinder\"\u003e2505EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for a dual system is \u003ca href=\"\/products\/dual-switch-6-way-sq-plug-6704\"\u003e6704\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ004R10-AJ-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAJ Single Leg Installation and Operation Manual, EQ004R10 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958748348475,"sku":"8414AMUPS","price":1870.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8414AMUPS-RVU.webp?v=1786536984"},{"product_id":"aj-hydraulic-trailer-jack-2-24-2-function-manual-selector","title":"AJ Hydraulic Trailer Jacks 2\/24 with 2 Function Manual Selector","description":"\u003ch3\u003eAJ hydraulic trailer jack, dual leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete dual leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AJ series is the 3.5\" x 3.5\" square tube in tube jack, and this system lifts 16,000 lbs across the two legs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAJ series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e16,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e3.5\" x 3.5\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eScrew drive output shaft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: screw drive\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is driven by hand through the output shaft on the end of the motor. Remove the pump top cover, then the silver sticker on the end of the motor, and drive the override coupler with a drill capable of at least 2000 rpm, using a 1\/4 inch (6mm) Allen drive hex key. Take care that the drill does not contact wires or hoses. The drill has to reach 2000 rpm or the pump will not develop enough pressure to move the jack.\u003c\/p\u003e\u003ch4\u003eTwo function manual selector\u003c\/h4\u003e\u003cp\u003eThis system is supplied with a two function manual selector, which lets the operator choose which function the pump drives by hand rather than through separate powered circuits.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-aj-hydraulic-trailer-jacks\"\u003e70487\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AJ dual leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/aj-70-cylinder\"\u003e2505EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for a dual system is \u003ca href=\"\/products\/dual-switch-6-way-sq-plug-6704\"\u003e6704\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ004R10-AJ-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAJ Single Leg Installation and Operation Manual, EQ004R10 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958748446779,"sku":"8415AMUPS","price":1970.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8415AM-Umounted.jpg?v=1786536987"},{"product_id":"am-1-24-with-m-o-screw-drive","title":"AM 1\/24 with Manual Override Screw Drive","description":"\u003ch3\u003eAM hydraulic trailer jack, single leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete single leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AM series is the 4\" x 4\" square tube in tube jack, and this system lifts 12,000 lbs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAM series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e12,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e4\" x 4\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eScrew drive output shaft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: screw drive\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is driven by hand through the output shaft on the end of the motor. Remove the pump top cover, then the silver sticker on the end of the motor, and drive the override coupler with a drill capable of at least 2000 rpm, using a 1\/4 inch (6mm) Allen drive hex key. Take care that the drill does not contact wires or hoses. The drill has to reach 2000 rpm or the pump will not develop enough pressure to move the jack.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eWireless remote option, part \u003ca href=\"\/products\/remote-control-part7823\"\u003e7823\u003c\/a\u003e for single function jacks\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-for-am-hydraulic-trailer-jacks\"\u003e70486\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AM single leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/am-24-cylinder\"\u003e1179EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for this single function system is \u003ca href=\"\/products\/single-switch-square-plug6526\"\u003e6526\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ005R9-AM-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAM Single Leg Installation and Operation Manual, EQ005R9 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958748938299,"sku":"8107UPS","price":1370.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8107UPS-RVU.webp?v=1786536992"},{"product_id":"hydraulic-bumper-pull-tj","title":"Hydraulic Bumper Pull TJ","description":"\u003ch3\u003eTJ hydraulic bumper pull tongue jack\u003c\/h3\u003e\u003cp\u003eComplete hydraulic tongue jack system designed for bumper pull applications, where a gooseneck or fifth wheel jack will not fit. Push button lifting on a bumper pull trailer removes the crank entirely.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e6,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e16\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eApplication\u003c\/th\u003e\n\u003ctd\u003eBumper pull trailers\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eStandard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eWhere the TJ sits in the range\u003c\/h4\u003e\u003cp\u003eThe TJ is the smallest jack in the EQ Systems trailer line at 6,000 lbs. Above it are the AJ at 8,000 lbs single and 16,000 lbs dual on a 24 inch stroke, and the AM at 12,000 lbs single and 24,000 lbs dual with 20, 24 and 30 inch stroke options. Four and six point automatic leveling systems are also available for trailers.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement cylinder is part \u003ca href=\"\/products\/tj-replacement-cylinder\"\u003e1218EQ\u003c\/a\u003e. TJ single leg systems run on the \u003ca href=\"\/products\/replacement-hydraulic-pump-3200ks\"\u003e3200KS\u003c\/a\u003e pump with reservoir 3333K and cover 70337. The switchgear for this single function system is \u003ca href=\"\/products\/single-switch-square-plug6526\"\u003e6526\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eWireless remote option, part \u003ca href=\"\/products\/remote-control-part7823\"\u003e7823\u003c\/a\u003e for single function jacks\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eA TJ bumper pull jack runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958749036603,"sku":"8065M","price":795.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8065M.jpg?v=1786536994"},{"product_id":"sl-24-heavy-duty-stacker-trailer-jack","title":"SL 24 Heavy Duty\/Stacker Trailer Jack","description":"\u003ch3\u003eSL 24 heavy duty stacker trailer jack\u003c\/h3\u003e\u003cp\u003eHeavy duty straight leg jack built for stacker trailers, where the nose weight and the height of the lift are both beyond what a standard trailer jack handles.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e17,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke\u003c\/th\u003e\n\u003ctd\u003e24 inch stroke cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCylinder\u003c\/th\u003e\n\u003ctd\u003eHeavy duty 3 inch cylinder with a 2 inch shaft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFoot pad\u003c\/th\u003e\n\u003ctd\u003eLarge 12 inch foot pad\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePump\u003c\/th\u003e\n\u003ctd\u003eCommercial single function pump with manual override screw drive\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eWeatherproof single switchgear control with key\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: screw drive\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is driven by hand through the output shaft on the end of the motor. Remove the pump top cover, then the silver sticker on the end of the motor, and drive the override coupler with a drill capable of at least 2000 rpm, using a 1\/4 inch (6mm) Allen drive hex key. Take care that the drill does not contact wires or hoses. The drill has to reach 2000 rpm or the pump will not develop enough pressure to move the jack.\u003c\/p\u003e\u003ch4\u003eWhy the heavy cylinder matters\u003c\/h4\u003e\u003cp\u003eThe 3 inch cylinder with a 2 inch shaft and the 12 inch foot pad are what separate this from a standard SL 24. The larger foot spreads the load on soft ground, which matters when a stacker is parked on gravel or grass with the full nose weight on one jack.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eSL 24 jacks are listed in the Jack Replacement Chart under parts \u003ca href=\"\/products\/sl-24-s\"\u003e7848\u003c\/a\u003e, 7923 and \u003ca href=\"\/products\/sl-24-a-17k\"\u003e70217\u003c\/a\u003e depending on plate position and rod diameter, with replacement feet \u003ca href=\"\/products\/12x12-foot-pad-with-bolt-7821\"\u003e7821\u003c\/a\u003e or 70299 and cylinders 3144EQ, 3184EQ or 3144AEQ. Measure the body length, plate position and rod diameter before ordering any service part.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eWireless remote option, part \u003ca href=\"\/products\/remote-control-part7823\"\u003e7823\u003c\/a\u003e for single function jacks\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn SL 24 stacker jack runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Jack-Replacement-Chart-Cylinder-Foot-identification-2025-V2.pdf\" target=\"_blank\"\u003eJack Replacement Cylinder and Foot Identification Chart (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS1004R3-EQ-Systems-Commercial.pdf\" target=\"_blank\"\u003eEQ Systems Hydraulic Jack Options, commercial range (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958749167675,"sku":"8662","price":1175.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/SL-24-2.jpg?v=1786536995"},{"product_id":"am2-24-w-m-ohand-pump-8176amups","title":"AM 2\/24 w\/Manual Override Hand Pump","description":"\u003ch3\u003eAM hydraulic trailer jack, dual leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete dual leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AM series is the 4\" x 4\" square tube in tube jack, and this system lifts 24,000 lbs across the two legs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAM series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e24,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e4\" x 4\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eHand pump\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: hand pump\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is worked by hand with a pump handle, no drill or power tool needed. To extend, install the handle in the hand pump and pump it; expect 10 to 20 strokes before enough pressure builds and the jack starts to move. To retract, locate the red knurled knob on the directional valve, pull it out and turn it a quarter turn so it stays out, then pump the handle. \u003cstrong\u003eReturn the directional valve to its normal position afterwards\u003c\/strong\u003e, rotating the knob until it snaps back, or the jack can drift down from the stowed position. The replacement handle is part \u003ca href=\"\/products\/handle-for-hand-pump\"\u003e1776\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-for-am-hydraulic-trailer-jacks\"\u003e70486\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AM dual leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/am-24-cylinder\"\u003e1179EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for a dual system is \u003ca href=\"\/products\/dual-switch-6-way-sq-plug-6704\"\u003e6704\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ005R9-AM-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAM Single Leg Installation and Operation Manual, EQ005R9 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958749331515,"sku":"8176AMUPS","price":2670.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8176AM-Mounted-w-cover_6837653d-376d-4b71-9ed8-9037e56d4eb2.jpg?v=1786536997"},{"product_id":"am-2-24-hydraulic-manual-override","title":"AM 2\/24 Hydraulic Jacks with Manual Override","description":"\u003ch3\u003eAM hydraulic trailer jack, dual leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete dual leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AM series is the 4\" x 4\" square tube in tube jack, and this system lifts 24,000 lbs across the two legs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAM series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e24,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e4\" x 4\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eScrew drive output shaft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: screw drive\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is driven by hand through the output shaft on the end of the motor. Remove the pump top cover, then the silver sticker on the end of the motor, and drive the override coupler with a drill capable of at least 2000 rpm, using a 1\/4 inch (6mm) Allen drive hex key. Take care that the drill does not contact wires or hoses. The drill has to reach 2000 rpm or the pump will not develop enough pressure to move the jack.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-for-am-hydraulic-trailer-jacks\"\u003e70486\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AM dual leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/am-24-cylinder\"\u003e1179EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for a dual system is \u003ca href=\"\/products\/dual-switch-6-way-sq-plug-6704\"\u003e6704\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ005R9-AM-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAM Single Leg Installation and Operation Manual, EQ005R9 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958764634171,"sku":"8074AMUPS","price":2375.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8074AMUPS.jpg?v=1786537187"}],"url":"https:\/\/eqsystems.us\/collections\/motorsports-cargo.oembed","provider":"EQ Systems","version":"1.0","type":"link"}