{"title":"Foot Pads","description":"\u003cp\u003eEQ Systems offers hydraulic lifting \u0026amp; leveling systems for the RV, horse trailer, motorsports, \u0026amp; commercial industries including options for hydraulic landing gear. With EQ Harness, we also offer custom wire harnesses.\u003c\/p\u003e\n","products":[{"product_id":"10x10-foot-pad-and-bolt-7849","title":"10x10 Foot Pad and Bolt #7849","description":"\u003ch3\u003e10 by 10 inch foot pad, EQ Systems part 7849\u003c\/h3\u003e\u003cp\u003eThe foot pad is the plate at the bottom of a hydraulic jack leg that carries the load into the ground. This is the 10 by 10 inch replacement pad, supplied with its bolt. It is the version for jack legs without a leg switch.\u003c\/p\u003e\u003ch4\u003eJacks this foot pad fits\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eSL 14 jack, part 7614, 2 7\/8 inch body plate mount, body length 18 1\/8\". Obsolete, contact EQ Systems.\u003c\/li\u003e\n\u003cli\u003eSL 16 jack, part \u003ca href=\"\/products\/sl-16-jack-w-o-leg-switch-7214\"\u003e7214\u003c\/a\u003e, 2 7\/8 inch body plate mount, body length 21 1\/8\". Body length was 20 1\/8 inches before 2023.\u003c\/li\u003e\n\u003cli\u003eSL 24 jack, part 70073, 2 7\/8 inch body plate mount, body length 28 3\/8\". Obsolete, replaced by \u003ca href=\"\/products\/sl-24-a-17k\"\u003e70217\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThose jacks are rated at 12k and 17.5k lifting capacity each.\u003c\/p\u003e\u003ch4\u003eIdentifying the right pad\u003c\/h4\u003e\u003cp\u003eMeasure your existing pad before ordering. An octagon pad is measured across the flats and a round pad across the diameter. Then confirm the jack itself: the body length is the fixed outer body of the jack, measured with the jack retracted, and the plate or bracket position is measured from the closed end of the body, positive toward the foot and negative past the closed end. Every EQ Systems jack, its body length, and the foot that belongs to it are listed in the chart below.\u003c\/p\u003e\u003cp\u003eA worn, bent or missing foot pad is worth replacing promptly on a system that uses leg switches. The switch is operated by the foot leaving and returning to the stowed position, so a missing foot will not operate the switch at all, a bent or distorted foot may not activate it properly, and a foot bent upward can damage or destroy the switch.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Jack-Replacement-Chart-Cylinder-Foot-identification-2025-V2.pdf\" target=\"_blank\"\u003eJack Replacement Cylinder and Foot Identification Chart (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958752739387,"sku":"7849","price":51.07,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/7849-RVU-scaled.webp?v=1786537051"},{"product_id":"10x10-foot-pad-leg-switch-7819","title":"10x10 Foot Pad Leg Switch #7819","description":"\u003ch3\u003e10 by 10 inch foot pad, EQ Systems part 7819\u003c\/h3\u003e\u003cp\u003eThe foot pad is the plate at the bottom of a hydraulic jack leg that carries the load into the ground. This is the 10 by 10 inch replacement pad, supplied with its bolt. It is the version for jack legs fitted with a plunger style leg switch, which is a different pad from the one used on legs without a switch.\u003c\/p\u003e\u003ch4\u003eJacks this foot pad fits\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eSL 12 jack, part 7064, leg with switch, body length 16\", foot width 8\". Obsolete. Replacement foot 7819 is now a 10 by 10 inch pad.\u003c\/li\u003e\n\u003cli\u003eSL 14 jack, part 7066, leg with switch, body length 18 1\/8\", foot width 10\". Obsolete, replaced by jack \u003ca href=\"\/products\/sl16-jack-leg-w-leg-switch7114\"\u003e7114\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003eSL 16 jack, part \u003ca href=\"\/products\/sl16-jack-leg-w-leg-switch7114\"\u003e7114\u003c\/a\u003e, leg with switch, body length 21 1\/8\", foot width 10\". Body length was 20 1\/8 inches before 2023.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThose jacks are rated at 12k lifting capacity each.\u003c\/p\u003e\u003ch4\u003eIdentifying the right pad\u003c\/h4\u003e\u003cp\u003eMeasure your existing pad before ordering. An octagon pad is measured across the flats and a round pad across the diameter. Then confirm the jack itself: the body length is the fixed outer body of the jack, measured with the jack retracted, and the plate or bracket position is measured from the closed end of the body, positive toward the foot and negative past the closed end. Every EQ Systems jack, its body length, and the foot that belongs to it are listed in the chart below.\u003c\/p\u003e\u003cp\u003eA worn, bent or missing foot pad is worth replacing promptly on a system that uses leg switches. The switch is operated by the foot leaving and returning to the stowed position, so a missing foot will not operate the switch at all, a bent or distorted foot may not activate it properly, and a foot bent upward can damage or destroy the switch.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Jack-Replacement-Chart-Cylinder-Foot-identification-2025-V2.pdf\" target=\"_blank\"\u003eJack Replacement Cylinder and Foot Identification Chart (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958752804923,"sku":"7819","price":83.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/7819-2.jpg?v=1786537053"},{"product_id":"12x12-ft-pad-for-legswitch7820","title":"12x12 ft Pad for LegSwitch#7820","description":"\u003ch3\u003e12 by 12 inch foot pad, EQ Systems part 7820\u003c\/h3\u003e\u003cp\u003eThe foot pad is the plate at the bottom of a hydraulic jack leg that carries the load into the ground. This is the 12 by 12 inch replacement pad, supplied with its bolt. It is the version for jack legs fitted with a plunger style leg switch, which is a different pad from the one used on legs without a switch.\u003c\/p\u003e\u003ch4\u003eJacks this foot pad fits\u003c\/h4\u003e\u003cul\u003e\u003cli\u003eSL 18 jack, part \u003ca href=\"\/products\/dp-18-jack-leg-with-leg-switch-7234\"\u003e7234\u003c\/a\u003e, leg with switch, body length 22 1\/8\", foot width 11.5\"\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eThose jacks are rated at 17.5k lifting capacity each.\u003c\/p\u003e\u003ch4\u003eIdentifying the right pad\u003c\/h4\u003e\u003cp\u003eMeasure your existing pad before ordering. An octagon pad is measured across the flats and a round pad across the diameter. Then confirm the jack itself: the body length is the fixed outer body of the jack, measured with the jack retracted, and the plate or bracket position is measured from the closed end of the body, positive toward the foot and negative past the closed end. Every EQ Systems jack, its body length, and the foot that belongs to it are listed in the chart below.\u003c\/p\u003e\u003cp\u003eA worn, bent or missing foot pad is worth replacing promptly on a system that uses leg switches. The switch is operated by the foot leaving and returning to the stowed position, so a missing foot will not operate the switch at all, a bent or distorted foot may not activate it properly, and a foot bent upward can damage or destroy the switch.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Jack-Replacement-Chart-Cylinder-Foot-identification-2025-V2.pdf\" target=\"_blank\"\u003eJack Replacement Cylinder and Foot Identification Chart (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958752870459,"sku":"7820","price":102.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/7820-2T.jpg?v=1787233753"},{"product_id":"12x12-foot-pad-with-bolt-7821","title":"12x12 Foot pad with Bolt #7821","description":"\u003ch3\u003e12 by 12 inch foot pad, EQ Systems part 7821\u003c\/h3\u003e\u003cp\u003eThe foot pad is the plate at the bottom of a hydraulic jack leg that carries the load into the ground. This is the 12 by 12 inch replacement pad, supplied with its bolt. It is the version for jack legs without a leg switch.\u003c\/p\u003e\u003ch4\u003eJacks this foot pad fits\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eSL 18 jack, part \u003ca href=\"\/products\/dp-18-jack-w-o-leg-switch-7134\"\u003e7134\u003c\/a\u003e, 3 3\/8 inch body plate mount, body length 22 3\/4\", plate position 1\", rod diameter 2\"\u003c\/li\u003e\n\u003cli\u003eSL 24 jack, part 7923, 3 3\/8 inch body plate mount, body length 29 1\/2\", plate position 8 1\/2\", rod diameter 2\". Body length was 29 inches before June 2023.\u003c\/li\u003e\n\u003cli\u003eSL 24 jack, part \u003ca href=\"\/products\/sl-24-s\"\u003e7848\u003c\/a\u003e, 3 3\/8 inch body plate mount, body length 29 1\/2\", plate position 14 1\/2\", rod diameter 2\". Body length was 29 inches before June 2023.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThose jacks are rated at 17.5k lifting capacity each.\u003c\/p\u003e\u003ch4\u003eIdentifying the right pad\u003c\/h4\u003e\u003cp\u003eMeasure your existing pad before ordering. An octagon pad is measured across the flats and a round pad across the diameter. Then confirm the jack itself: the body length is the fixed outer body of the jack, measured with the jack retracted, and the plate or bracket position is measured from the closed end of the body, positive toward the foot and negative past the closed end. Every EQ Systems jack, its body length, and the foot that belongs to it are listed in the chart below.\u003c\/p\u003e\u003cp\u003eA worn, bent or missing foot pad is worth replacing promptly on a system that uses leg switches. The switch is operated by the foot leaving and returning to the stowed position, so a missing foot will not operate the switch at all, a bent or distorted foot may not activate it properly, and a foot bent upward can damage or destroy the switch.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Jack-Replacement-Chart-Cylinder-Foot-identification-2025-V2.pdf\" target=\"_blank\"\u003eJack Replacement Cylinder and Foot Identification Chart (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958752935995,"sku":"7821","price":95.36,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/7821-2.jpg?v=1786537055"},{"product_id":"70385-7-x-7-foot-pad-with-lock-nut","title":"7 X 7 Foot Pad with Lock Nut #70385","description":"\u003ch3\u003e7 by 7 inch foot pad, EQ Systems part 70385\u003c\/h3\u003e\u003cp\u003eThe foot pad is the plate at the bottom of a hydraulic jack leg that carries the load into the ground. This is the 7 by 7 inch replacement pad, supplied with its lock nut. It is the version for jack legs without a leg switch.\u003c\/p\u003e\u003ch4\u003eJacks this foot pad fits\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eSL 11 jack, part 70348, C-channel bracket, body length 14 3\/8\", bracket position 7 1\/4\"\u003c\/li\u003e\n\u003cli\u003eSL 12 jack, part 70437, C-channel bracket, body length 15 3\/8\", bracket position 7 1\/4\"\u003c\/li\u003e\n\u003cli\u003eSL 13 jack, part 70381, C-channel bracket, body length 16 3\/8\", bracket position 7 1\/4\"\u003c\/li\u003e\n\u003cli\u003eSL 13 jack, part 70309EQ \/ 70310EQ, C-channel bracket, body length 16 3\/8\", bracket position -1\/2\". Identical cylinders with the mounting bracket on opposite sides.\u003c\/li\u003e\n\u003cli\u003eSL 13 jack, part 70269 \/ 70270, C-channel bracket, body length 16 3\/8\", bracket position -1 1\/4\". Identical cylinders with the mounting bracket on opposite sides.\u003c\/li\u003e\n\u003cli\u003eSL 11 jack, part 7841, 2 3\/8 inch body plate mount, body length 15 3\/8\", plate position 0\"\u003c\/li\u003e\n\u003cli\u003eSL 13 jack, part \u003ca href=\"\/products\/sl-13-hp-jack-without-leg-switch\"\u003e7842\u003c\/a\u003e, 2 3\/8 inch body plate mount, body length 17 3\/8\", plate position 0\". Obsolete, contact EQ Systems.\u003c\/li\u003e\n\u003cli\u003eSL 13 jack, part \u003ca href=\"\/products\/sl-13-hp-jack-without-leg-switch\"\u003e7842\u003c\/a\u003e, 2 3\/8 inch body plate mount, body length 16 3\/8\", plate position -7\/8\"\u003c\/li\u003e\n\u003cli\u003eSL 13 jack, part \u003ca href=\"\/products\/sl-13-lp-jack-without-leg-switch\"\u003e7842A\u003c\/a\u003e, 2 3\/8 inch body plate mount, body length 16 3\/8\", plate position 2\"\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThose jacks are rated at 7.5k lifting capacity each.\u003c\/p\u003e\u003ch4\u003eIdentifying the right pad\u003c\/h4\u003e\u003cp\u003eMeasure your existing pad before ordering. An octagon pad is measured across the flats and a round pad across the diameter. Then confirm the jack itself: the body length is the fixed outer body of the jack, measured with the jack retracted, and the plate or bracket position is measured from the closed end of the body, positive toward the foot and negative past the closed end. Every EQ Systems jack, its body length, and the foot that belongs to it are listed in the chart below.\u003c\/p\u003e\u003cp\u003eA worn, bent or missing foot pad is worth replacing promptly on a system that uses leg switches. The switch is operated by the foot leaving and returning to the stowed position, so a missing foot will not operate the switch at all, a bent or distorted foot may not activate it properly, and a foot bent upward can damage or destroy the switch.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Jack-Replacement-Chart-Cylinder-Foot-identification-2025-V2.pdf\" target=\"_blank\"\u003eJack Replacement Cylinder and Foot Identification Chart (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958761685051,"sku":"70385","price":48.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/3202-3203-scaled_2072377a-9974-4f9a-b1db-5ab4d80bc0d8.jpg?v=1786537146"},{"product_id":"10x10-foot-pad-with-screw-7818","title":"10 X 10 Foot Pad with Screw #7818","description":"\u003ch3\u003e10 by 10 inch foot pad, EQ Systems part 7818\u003c\/h3\u003e\u003cp\u003eThe foot pad is the plate at the bottom of a hydraulic jack leg that carries the load into the ground. This is the 10 by 10 inch replacement pad, supplied with its screw. It is the version for jack legs without a leg switch.\u003c\/p\u003e\u003ch4\u003eJacks this foot pad fits\u003c\/h4\u003e\u003cul\u003e\u003cli\u003eSL 15 jack, part \u003ca href=\"\/products\/sl-15-jack-without-leg-switch\"\u003e7636\u003c\/a\u003e, 2 3\/8 inch body plate mount, body length 19 3\/8\", plate position 0\"\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eThose jacks are rated at 7.5k lifting capacity each.\u003c\/p\u003e\u003ch4\u003eIdentifying the right pad\u003c\/h4\u003e\u003cp\u003eMeasure your existing pad before ordering. An octagon pad is measured across the flats and a round pad across the diameter. Then confirm the jack itself: the body length is the fixed outer body of the jack, measured with the jack retracted, and the plate or bracket position is measured from the closed end of the body, positive toward the foot and negative past the closed end. Every EQ Systems jack, its body length, and the foot that belongs to it are listed in the chart below.\u003c\/p\u003e\u003cp\u003eA worn, bent or missing foot pad is worth replacing promptly on a system that uses leg switches. The switch is operated by the foot leaving and returning to the stowed position, so a missing foot will not operate the switch at all, a bent or distorted foot may not activate it properly, and a foot bent upward can damage or destroy the switch.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Jack-Replacement-Chart-Cylinder-Foot-identification-2025-V2.pdf\" target=\"_blank\"\u003eJack Replacement Cylinder and Foot Identification Chart (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958764404795,"sku":"7818","price":61.27,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/7818wbolt.jpg?v=1786537185"}],"url":"https:\/\/eqsystems.us\/collections\/foot-pads.oembed","provider":"EQ Systems","version":"1.0","type":"link"}