{"title":"Dual Leg","description":"\u003cp\u003eWith EQ Systems’ hydraulic dual leg lifting system, we make parking and setting up your Horse Trailer a breeze. With our Hydraulic Lifting Systems, you can quickly and safely secure your Horse Trailer with one touch of a button – no more manual labor or guesswork.\u003c\/p\u003e\n\u003cp\u003ePlus, it’s easy to maintain, so you can enjoy your leisure time worry-free!\u003c\/p\u003e\n\u003cp\u003eWe are located in Cassopolis, Michigan, at 19300 Grange St, Cassopolis, MI 49031 for installations.\u003c\/p\u003e","products":[{"product_id":"aj-2-24-jack-system","title":"AJ 2\/24 Jack System","description":"\u003ch3\u003eAJ hydraulic trailer jack, dual leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete dual leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AJ series is the 3.5\" x 3.5\" square tube in tube jack, and this system lifts 16,000 lbs across the two legs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAJ series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e16,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e3.5\" x 3.5\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eScrew drive output shaft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: screw drive\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is driven by hand through the output shaft on the end of the motor. Remove the pump top cover, then the silver sticker on the end of the motor, and drive the override coupler with a drill capable of at least 2000 rpm, using a 1\/4 inch (6mm) Allen drive hex key. Take care that the drill does not contact wires or hoses. The drill has to reach 2000 rpm or the pump will not develop enough pressure to move the jack.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-aj-hydraulic-trailer-jacks\"\u003e70487\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AJ dual leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/aj-70-cylinder\"\u003e2505EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for a dual system is \u003ca href=\"\/products\/dual-switch-6-way-sq-plug-6704\"\u003e6704\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ004R10-AJ-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAJ Single Leg Installation and Operation Manual, EQ004R10 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958748348475,"sku":"8414AMUPS","price":1870.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8414AMUPS-RVU.webp?v=1786536984"},{"product_id":"aj-hydraulic-trailer-jack-2-24-2-function-manual-selector","title":"AJ Hydraulic Trailer Jacks 2\/24 with 2 Function Manual Selector","description":"\u003ch3\u003eAJ hydraulic trailer jack, dual leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete dual leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AJ series is the 3.5\" x 3.5\" square tube in tube jack, and this system lifts 16,000 lbs across the two legs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAJ series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e16,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e3.5\" x 3.5\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eScrew drive output shaft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: screw drive\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is driven by hand through the output shaft on the end of the motor. Remove the pump top cover, then the silver sticker on the end of the motor, and drive the override coupler with a drill capable of at least 2000 rpm, using a 1\/4 inch (6mm) Allen drive hex key. Take care that the drill does not contact wires or hoses. The drill has to reach 2000 rpm or the pump will not develop enough pressure to move the jack.\u003c\/p\u003e\u003ch4\u003eTwo function manual selector\u003c\/h4\u003e\u003cp\u003eThis system is supplied with a two function manual selector, which lets the operator choose which function the pump drives by hand rather than through separate powered circuits.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-aj-hydraulic-trailer-jacks\"\u003e70487\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AJ dual leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/aj-70-cylinder\"\u003e2505EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for a dual system is \u003ca href=\"\/products\/dual-switch-6-way-sq-plug-6704\"\u003e6704\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ004R10-AJ-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAJ Single Leg Installation and Operation Manual, EQ004R10 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958748446779,"sku":"8415AMUPS","price":1970.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8415AM-Umounted.jpg?v=1786536987"},{"product_id":"am2-24-w-m-ohand-pump-8176amups","title":"AM 2\/24 w\/Manual Override Hand Pump","description":"\u003ch3\u003eAM hydraulic trailer jack, dual leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete dual leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AM series is the 4\" x 4\" square tube in tube jack, and this system lifts 24,000 lbs across the two legs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAM series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e24,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e4\" x 4\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eHand pump\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: hand pump\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is worked by hand with a pump handle, no drill or power tool needed. To extend, install the handle in the hand pump and pump it; expect 10 to 20 strokes before enough pressure builds and the jack starts to move. To retract, locate the red knurled knob on the directional valve, pull it out and turn it a quarter turn so it stays out, then pump the handle. \u003cstrong\u003eReturn the directional valve to its normal position afterwards\u003c\/strong\u003e, rotating the knob until it snaps back, or the jack can drift down from the stowed position. The replacement handle is part \u003ca href=\"\/products\/handle-for-hand-pump\"\u003e1776\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-for-am-hydraulic-trailer-jacks\"\u003e70486\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AM dual leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/am-24-cylinder\"\u003e1179EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for a dual system is \u003ca href=\"\/products\/dual-switch-6-way-sq-plug-6704\"\u003e6704\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ005R9-AM-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAM Single Leg Installation and Operation Manual, EQ005R9 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958749331515,"sku":"8176AMUPS","price":2670.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8176AM-Mounted-w-cover_6837653d-376d-4b71-9ed8-9037e56d4eb2.jpg?v=1786536997"},{"product_id":"solar-panel-kit-aj-hydraulic-trailer-jacks","title":"Solar Panel Kit for AJ Hydraulic Trailer Jacks","description":"\u003ch3\u003eSolar panel kit for AJ hydraulic trailer jacks, part 70487\u003c\/h3\u003e\u003cp\u003eKeeps the jack battery topped up from sunlight, so a trailer parked between trips still has the power to run its jacks. This kit fits all AJ single and dual hydraulic trailer jacks.\u003c\/p\u003e\u003ch4\u003eWhy a trailer jack needs charge support\u003c\/h4\u003e\u003cp\u003eEQ Systems hydraulic pumps are not light loads: EQ Systems specifies a battery that load tests at 150 amperes at 10.5 VDC for at least 30 seconds. A trailer battery that has sat for weeks will often crank a jack part way and stall, which reads as a pump fault when it is a power fault.\u003c\/p\u003e\u003ch4\u003eThe AJ series\u003c\/h4\u003e\u003cp\u003eAJ jacks lift 8,000 lbs single and 16,000 lbs dual, with a 24 inch stroke on a 3.5 by 3.5 inch tube. Manual override is standard on both, so a flat battery never leaves you stranded, but it does mean cranking by hand or with a drill.\u003c\/p\u003e\u003ch4\u003eOther ways to keep the battery up\u003c\/h4\u003e\u003cp\u003eIf the trailer is regularly connected to a tow vehicle, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the vehicle instead, using 4 gauge copper cable and a resettable 100 amp breaker.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958763487291,"sku":"70487","price":146.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/70487-AJ-SOLAR-KIT.jpg?v=1786537173"},{"product_id":"solar-panel-kit-for-am-hydraulic-trailer-jacks","title":"Solar Panel Kit for AM Hydraulic Trailer Jacks","description":"\u003ch3\u003eSolar panel kit for AM hydraulic trailer jacks, part 70486\u003c\/h3\u003e\u003cp\u003eKeeps the jack battery topped up from sunlight, so a trailer parked between trips still has the power to run its jacks. This kit fits all AM single and dual hydraulic trailer jacks.\u003c\/p\u003e\u003ch4\u003eWhy a trailer jack needs charge support\u003c\/h4\u003e\u003cp\u003eEQ Systems hydraulic pumps are not light loads: EQ Systems specifies a battery that load tests at 150 amperes at 10.5 VDC for at least 30 seconds. A trailer battery that has sat for weeks will often crank a jack part way and stall, which reads as a pump fault when it is a power fault.\u003c\/p\u003e\u003ch4\u003eThe AM series\u003c\/h4\u003e\u003cp\u003eAM jacks lift 12,000 lbs single and 24,000 lbs dual, with 20, 24 and 30 inch stroke options on a 4 by 4 inch tube. Manual override is standard on both, so a flat battery never leaves you stranded, but it does mean cranking by hand or with a drill.\u003c\/p\u003e\u003ch4\u003eOther ways to keep the battery up\u003c\/h4\u003e\u003cp\u003eIf the trailer is regularly connected to a tow vehicle, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the vehicle instead, using 4 gauge copper cable and a resettable 100 amp breaker.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958763585595,"sku":"70486","price":146.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/70487-AJ-SOLAR-KIT_d7114cc6-aee5-4932-a467-56ad262c6900.jpg?v=1786537174"},{"product_id":"am-2-24-hydraulic-manual-override","title":"AM 2\/24 Hydraulic Jacks with Manual Override","description":"\u003ch3\u003eAM hydraulic trailer jack, dual leg, 24\" stroke\u003c\/h3\u003e\u003cp\u003eComplete dual leg hydraulic lifting system for a gooseneck or fifth wheel trailer. The AM series is the 4\" x 4\" square tube in tube jack, and this system lifts 24,000 lbs across the two legs. Push button lifting replaces cranking a manual jack, which on a loaded horse or motorsports trailer is the difference between a two minute hook up and a fight.\u003c\/p\u003e\u003ch4\u003eSpecifications\u003c\/h4\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eAM series tube in tube\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLegs\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLifting capacity\u003c\/th\u003e\n\u003ctd\u003e24,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eStroke length\u003c\/th\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube size\u003c\/th\u003e\n\u003ctd\u003e4\" x 4\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eManual override\u003c\/th\u003e\n\u003ctd\u003eScrew drive output shaft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eControl\u003c\/th\u003e\n\u003ctd\u003eKeyed switch and harness, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch4\u003eManual override: screw drive\u003c\/h4\u003e\u003cp\u003eIf the system loses power, the jack is driven by hand through the output shaft on the end of the motor. Remove the pump top cover, then the silver sticker on the end of the motor, and drive the override coupler with a drill capable of at least 2000 rpm, using a 1\/4 inch (6mm) Allen drive hex key. Take care that the drill does not contact wires or hoses. The drill has to reach 2000 rpm or the pump will not develop enough pressure to move the jack.\u003c\/p\u003e\u003ch4\u003eStandard and optional equipment\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eKeyed switch and harness standard, which also prevents unauthorized use of the system\u003c\/li\u003e\n\u003cli\u003eUniversal mounting brackets included\u003c\/li\u003e\n\u003cli\u003eSwitchgear built in house, performance verification tested, braided nylon exterior\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBattery requirement\u003c\/h4\u003e\u003cp\u003eEQ Systems recommends a minimum group 24 RV or marine battery rated at least 100 minutes reserve capacity and 500 cold cranking amps; the higher those numbers the better. Flooded lead acid, gel and AGM types are all suitable. Some lithium batteries cannot deliver the running amperage this system needs, so check with the battery manufacturer before fitting one. If the trailer sits between trips, Stay Charge parts \u003ca href=\"\/products\/stay-charge\"\u003e8400\u003c\/a\u003e and \u003ca href=\"\/products\/stay-charge-with-jumper-cables\"\u003e8427\u003c\/a\u003e charge the trailer battery from the tow vehicle, and solar kit \u003ca href=\"\/products\/solar-panel-kit-for-am-hydraulic-trailer-jacks\"\u003e70486\u003c\/a\u003e keeps the jack battery topped up.\u003c\/p\u003e\u003ch4\u003eFluid and maintenance\u003c\/h4\u003e\u003cp\u003eAn AM dual leg system runs on Dexron III ATF, filled to about one inch below the top of the reservoir with the jacks fully retracted. Remember the level rises as the jacks retract. The reservoir must run with its vented breather cap fitted, not the flush shipping plug, or the jack will operate erratically. EQ Systems recommends owners inspect the system every 12 months, checking that all connections are tight and free from corrosion, particularly the ground to the pump stud and the positive cable to the motor solenoid.\u003c\/p\u003e\u003ch4\u003eService parts\u003c\/h4\u003e\u003cp\u003eThe replacement hydraulic cylinder for this jack is part \u003ca href=\"\/products\/am-24-cylinder\"\u003e1179EQ\u003c\/a\u003e. Cylinders are identified by the jack outer tube size and length, not by the bracket. The switchgear for a dual system is \u003ca href=\"\/products\/dual-switch-6-way-sq-plug-6704\"\u003e6704\u003c\/a\u003e.\u003c\/p\u003e\u003ch4\u003eDocuments\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQS03R11-EQ-Systems-Trailer.pdf\" target=\"_blank\"\u003eEQ Systems Lifting Systems for Any Size Trailer (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/EQ005R9-AM-Single-Leg-Insallation-Opertion-Manual-TM.pdf\" target=\"_blank\"\u003eAM Single Leg Installation and Operation Manual, EQ005R9 (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/TS-Single-leg-Trailer-Jacks-AM-AJ-single-manufactured-after-2007.pdf\" target=\"_blank\"\u003eSingle Leg Trailer Jack Troubleshooting Guide (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Hydraulic_Cylinder_Identification_for_Tube-in-Tube_Jacks.pdf\" target=\"_blank\"\u003eHydraulic Cylinder Identification for Tube in Tube Jacks (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/cdn\/shop\/files\/Required-Maintenance-Items-Hydraulic-Systems-EQ-TM.pdf\" target=\"_blank\"\u003eRequired Maintenance Items for EQ Systems Hydraulic Jacks and Slide Systems (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EQ Systems","offers":[{"title":"Default Title","offer_id":43958764634171,"sku":"8074AMUPS","price":2375.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2608\/6971\/files\/8074AMUPS.jpg?v=1786537187"}],"url":"https:\/\/eqsystems.us\/collections\/dual-leg-horse-trailers.oembed","provider":"EQ Systems","version":"1.0","type":"link"}